A starting point for your project

Vehicle repair workshop design 15 × 24 m starting form

Bring vehicle bays, lifts and the service bench into one clear layout. The open-front workshop concept helps you compare access and working space before fixing the openings, services and equipment foundations.

Open this concept in 3D Explore quantities

यह जानकारी हिंदी में पढ़ें

Furnished vehicle repair workshop 3D concept showing the frame and illustrative interior equipment — Illustrative preset preview. Current starting inputs are listed below; inspect changes in the live editor.

Floor footprint: 360 m²15 × 24 m width × length
Eave height: 5 mCheck actual underside clearance
Bays along the length: 4 bays6.00 m centre-to-centre
Wall arrangement: Three sides clad · open frontStructural members remain at openings

Same footprint. Three bay arrangements.

See what changes the steel quantity.

The range compares 3, 4, 5 bays at the same width, length, eave, roof, openings and selected sections. It describes those modelled arrangements; it is not an engineered minimum–maximum allowance.

31.5–37.6kg/m² of floor footprint

2.93–3.49kg/sq ft of floor footprint

Concept take-off, sections not designed — run the section sizing screen

Starting 4-bay model: 12,400 kg of modelled steel.

See exact scenarios and quantity basis

Bays	Bay spacing (m)	Model steel (kg)	kg/m²	kg/sq ft
3	8.00	11,349	31.52	2.929
4starting	6.00	12,400	34.44	3.200
5	4.80	13,528	37.58	3.491

Primary / secondary / brace sections: BSP MB 300 × 140 · MC 100 × 50 · ISA 75 × 75 × 6

End-wall framing is enabled, matching a fresh editor preset; modelled end posts are included where walls are clad. This is net frame, secondary-member and plate mass. Procurement waste, cladding, civil works, furnishings and equipment loads remain separate. No price, safe capacity or design approval is inferred.

More than an empty shell

A furnished starting layout.

The current fit-out generator places 12 physical objects in this starting model. These counts come from that generated layout.

2
Two-post vehicle liftVehicle lift bay
1
Workshop benchService bench
2
Generic service vehicleVehicle reservation
1
Storage cabinetService tools
1
Utility sinkUtility sink
3
Linear light fixtureGeneral light
2
Extinguisher positionFire equipment position (review required)

The 3.0 m central stripe is a planning reserve, not an approved exit route or vehicle swept-path result. Equipment is generic; confirm capacity, service clearances and actual loads separately.

Before you build your brief

Questions, answered.

A closer look at the vehicle repair workshop concept, its editable inputs and the decisions that belong in a project-specific design.

What are the starting dimensions of the vehicle repair workshop?

The preset starts at 15 m wide by 24 m long, with a 5 m eave and 4 bays along its length. You can edit these dimensions. They describe a concept starting form, not an operating capacity or approved structural design.

Are the two vehicle lifts rated for real vehicles?

They are generic editable meshes with no load rating or installation approval. Obtain the lift manufacturer's dimensions, operating envelope, base reactions and anchorage requirements.

Does the open front provide enough vehicle access?

The front cladding is omitted, but structural members remain. Check the complete approach, turning path, opening width and height against the actual vehicles and lift positions.

Are the lift bases and workshop floor designed?

No. The model does not calculate slab capacity, reinforcement or lift anchorage. These depend on equipment reactions, foundation details, soil conditions and the project design.

Can I add a wash or paint bay?

You can coordinate additional objects and partitions, but drainage, ventilation, extraction, electrical classification and fire provisions for the chosen activity must be separately specified.

Explore another starting point

View all 20 concepts